Description:

The protective coat is specially formulated to protect, seal, and waterproof floors, countertops, and any other epoxy surface. A clear varnish providing extra resistance, it reaches full cure in 7 days. Ideal for restoring an existing scratched epoxy floor or on a freshly applied epoxy surface. Perfect solution for a satin finish while benefiting from the thickness of the epoxy.

Interior use only. This product is not resistant to tire marks from vehicles and does not offer the same chemical resistance as PE 100% solid epoxy.

The epoxy finish varnish was not designed to be applied to bare concrete surfaces (sealed or unsealed).

• 100% polyurethane
• Ready-to-use
• Extra protection for abrasion and impact resistance
• Quick drying
• Acts as a dust-proofing sealer
• Full cure in 7 days
• Easy to work with and levels well
• Low, non-offensive odor
• Low VOC content (272 g/L)
• Non-flammable

RECOMMENDED LOCATIONS

• Residential: basement floors, epoxy countertops
• Utility garage: Warning! The product is not designed to resist oil and heat from tires (especially with new tires).
• Commercial: restaurants, retail stores, shopping centers, offices, and hotels

RECOMMENDED APPLICATORS

• 10 mm lint-free roller (3/8 in)
• Brush
• Finitec varnish applicator

APPLICATION CONDITIONS*

• Temperature between 21°C and 25°C (70°F and 77°F)
• Relative humidity between 35% and 50%

* Refer to the Drying and Curing Time section of this document.

FLOOR PREPARATION

1- Sweep or vacuum to remove dust, dirt, and other debris. Pay special attention to corners.

2- Clean thoroughly with Finitec Surface Prep to remove accumulated dirt and rinse.

3- Scuff the surface with a sander and 120-grit sandpaper (or an orbital sander and 120-grit sandpaper).

4- Thoroughly remove dust with a vacuum or damp towels.

NOTE: Perform a preliminary test on a section by reproducing actual application conditions and methods to verify adhesion, compatibility, and product color.

PREPARATION AND MIXING

Stir with a clean stick to ensure product homogeneity. Mix vigorously for at least 45 seconds. Let stand for at least 10 minutes to allow bubbles to disperse.

NOTE: DO NOT dilute.

APPLICATION METHOD (10mm roller)

NOTE: Turn off all ventilation in the room. If ventilation cannot be turned off, block all vents for minimum air movement in the room.

1- Ensure the epoxy surface is clean and dry, free of wax, grease, or oil.

2- DO NOT use if the surface temperature, ambient temperature, or concrete slab temperature is below 15°C.

3- Pour a generous amount of the protective coat into a paint tray.

4- Use the 15 cm (6 in) Finitec applicator or a clean brush, soak, and apply a strip around the perimeter of the floor.

5- Thoroughly soak the roller. In a corner of the room, on a section of approximately 4 ft x 4 ft, place the roller in the center and roll in a back-and-forth motion.

6- Then go over it in the opposite direction and eliminate streaks by lifting the roller at the end of the stroke.

7- Overlap each section by a width of about 6 in.

NOTE: DO NOT apply too thin a coat (refer to the Coverage section in the technical data of this document).

8- Continue this way across the entire floor.

9- Allow 3 to 4 hours of drying time between coats (may vary depending on ambient conditions).

Do not exceed 24 hours between coats.

NOTE: It is recommended to apply 2 coats. For optimal results, 1 to 2 additional coats may be applied.

10- Sand between coats with a sander and 180-grit sandpaper.

11- Remove dust using a vacuum or damp towels.

NOTE: It is not necessary to sand before the final coat if the time between the last two applications does not exceed 3-4 hours. For the gloss finish, do not sand between the last two coats.

12- Clean tools with water.

CONCRETE SURFACE

This product was not designed to be applied to bare concrete surfaces (sealed or unsealed). We are therefore not responsible for the results of such use. Please perform application tests beforehand.

DRYING AND CURING TIME

The curing process is approximately 7 days (100% cure after 7 days, 90% after 48-72 hours, and 75% after 24 hours). To optimize the performance of the protective coat, it is important to wait for full cure before the first wet cleaning. After 4 hours of drying time, light traffic is permitted. Traffic is possible after 24 hours; however, the floor may scratch or scuff. The curing process must be respected (refer to the Technical Data in this document).

NOTE: The drying and curing times mentioned in this document may vary depending on application conditions: lower temperature (ambient air and/or slab), higher humidity, or a thicker application of product on the floor could slow down the drying and curing processes.

MAINTENANCE AND PREVENTION

For a garage surface, take precautions and wait 5 to 7 days before parking a vehicle.

However, keep in mind that car tires can sometimes leave black marks on the varnish caused by heat and oil found in the rubber.

Use protective felt pads under furniture and storage units to prevent scratches.

Do not slide or drag furniture across the floor.

Vacuum or sweep regularly to prevent the finish from being scratched.

FIRST AID

In case of contact with eyes or skin, rinse thoroughly with water for 15 minutes. If inhaled, move the person to fresh air. If swallowed, call a doctor. Do not induce vomiting. If the person is conscious, have them drink a few glasses of water. Keep out of reach of children.

Technical documents